How to Build a Fire in Wet Weather: Practical Backcountry Techniques

Learning how to build a fire in wet weather is an important backcountry skill. After several days of rain, when the ground is soaked and nearly everything feels damp, getting a dependable fire going takes more preparation than simply striking a match.

The key is knowing where to find usable wood, how to prepare it, and how to develop enough heat to keep it burning.

Finding Dry Firewood in Wet Conditions

When everything is wet, don’t automatically gather the first deadwood you find lying on the ground. Much of it may be waterlogged or beginning to rot.

Instead, look for dead lower branches still attached to evergreen trees. These are often protected from rain and ground moisture.

Other good places to check include the undersides of downed logs, sheltered twigs beneath dense evergreen branches, and deadwood beneath natural rock overhangs.

Standing dead timber can also provide good firewood, particularly when split to expose the interior. However, even standing dead trees can contain considerable moisture, especially near the base.

Look for sound wood that feels firm when cut or split. Wood that crumbles apart or is wet throughout generally isn’t worth the trouble.

Preparing Kindling From Damp Wood

Even when the outside of a piece of wood is wet, the inside may still be dry enough to burn.

Use a hatchet or knife to split suitable deadwood into smaller pieces. Once you reach the dry interior, shave thin curls or make feather sticks that will catch a flame more readily.

Prepare several sizes of kindling, from fine shavings to small sticks.

One of the most important lessons is to gather more dry kindling than you think you’ll need before lighting the fire.

Running out of prepared kindling while trying to establish a flame is an unnecessary frustration.

Always Carry a Fire-Starting Kit

Fatwood, feather sticks, split kindling, lighter, and matches prepared for building a fire in wet weather

During my years in the backcountry, I always carried a small waterproof container with fire-starting supplies.

Inside were a lighter, matches, commercial fire-starting sticks, and a bundle of fatwood.

I split the fatwood into narrow pieces approximately twice the thickness of a wooden matchstick. Its resin content helps it ignite readily and produce a strong flame, even when conditions are damp.

A kit like this takes up little room and can make a considerable difference when you’re cold, wet, and trying to get a fire established.

Building the Fire

Start by choosing a location with some protection from wind and rain.

If the ground is saturated, build a small platform of dry sticks or split wood to keep the starting fire off the wet soil.

Small campfire burning on a platform of sticks and split wood above wet forest ground

Place your fire starter on the platform and arrange small, dry kindling around it.

A teepee or log-cabin arrangement will work. The important thing is leaving enough room between the sticks for air to circulate.

Light the starter and allow the smallest pieces to catch before gradually adding larger kindling.

Don’t rush to put big pieces of wood on the fire. Build a strong flame and a bed of hot coals first.

Once the fire is established, you can begin adding larger split pieces, including wood that still contains some moisture.

If necessary, place damp firewood near the heat to begin drying it before use, keeping it safely clear of the flames.

Choosing Firewood That Produces Good Heat

In our Idaho backcountry camps, we burned mainly lodgepole pine and Douglas fir, sometimes called red fir.

Both worked well, although we found Douglas fir generally produced more heat than lodgepole.

Small dead branches were useful for starting fires, while larger split pieces provided more sustained heat.

The species available will vary depending on the country, but sound wood with a reasonably dry interior is generally preferable to material that’s soaked or rotten.

When Your Fire Won’t Stay Lit

If your fire keeps smoking or dying down, adding more wood isn’t necessarily the answer.

First, check the kindling. If it’s damp, replace it with drier material or shave some fresh kindling from the inside of a split piece.

Next, check the airflow. Sticks packed too tightly together can prevent the fire from getting enough oxygen.

If larger logs were added too soon, remove some of them and rebuild the flame with smaller pieces.

Concentrating the burning material and hot coals can also help restore heat.

Finally, make sure wind or rain isn’t repeatedly weakening the flames.

A smoking fire isn’t necessarily a growing fire. If it continues to smolder, something needs to change.

Preparing Firewood for Backcountry Camp

When establishing a longer-term hunting camp, having a supply of prepared firewood saves considerable work during bad weather.

Over the years, we used crosscut saws, axes, splitting mauls, hatchets, and chainsaws where permitted to cut and prepare firewood.

Larger pieces were cut into manageable lengths and split, while smaller branches were used for kindling.

We kept our firewood supply protected from the weather, often covering the main woodpile with a tarp.

It’s also important to know the regulations where you’re camping. Chainsaws and other motorized equipment are generally prohibited in designated wilderness without specific authorization, and fire restrictions may limit whether you can build a fire at all.

Final Thoughts

Building a dependable fire in wet weather comes down to preparation.

Find sound wood, split it to reach the dry interior, prepare plenty of kindling, and build your fire gradually until you have enough heat to sustain larger pieces.

Carry a reliable fire-starting kit and practice these skills before you find yourself depending on them.

Above all, be patient. A few extra minutes preparing your materials can save a lot of frustration trying to keep a poorly started fire burning.